Polyether ether ketone (PEEK) plastic

/in , , /by

PEEK, which an aromatic crystalline thermoplastic polymer material, the melting point of 334 ℃, the following is a charming feature: short-term heat resistance by adding glass fiber or carbon acid after heat distortion temperature up to above 300 ℃; long-term heat resistance index for the UL 250 ℃; toughness, resistance, However, up to UL-0 level, can be self-extinguishing, and smokeless; resistance to drugs of good performance, only soluble in concentrated sulfuric acid. Another good processing behavior, its also resistance to radiation, resistance to peeling, electrical properties, fatigue resistance, impact resistance wear resistance, hydrolysis resistance and other properties are very good, which is a rare engineering plastic. 

PEEK injection molding is an important part of medical, industry, electronics, etc. if you need PEEK molding parts for your project, you are welcome to contact us, we have done lots of this PEEK molded parts, PPSU molding parts, PEI molding parts, etc.

Because of its good overall performance, they are widely used: 

    Extrusion: the magnet wire coating using PEEK has good machinability and good resistance to peel, good abrasion resistance and good resistance to radiation and strong, free coloring, etc. have been used as a cable, wire insulation, and protection layer. Widely used in atomic energy, aircraft, ships, oil, gas, magnet wire, fiber optics, and other fields; films use its moisture absorption of small, acid-resistant solder, etc., for H-class and C class insulation material widely used in motors, generators, transformer insulating film, and orbit of printed circuit board, the carrier belt, heat resistant with other drugs ring; PEEK monofilament fiber using steam-resistant, anti-drugs, wear resistance, creep resistance, toughness, etc. Paper machine drying applied to canvas, heat Shanghai cloth, racket cable, composite materials, heat-resistant woven with other drugs. Injection molding: the wear-resistant materials, its wear resistance, resistance to drugs, toughness, and can be used at 250 ℃, etc. for the manufacture of bearing cage, the metal bearing the protection lining, clutch parts, power brake vacuum parts, gasoline engines parts, wheels loader blade, copier parts, suspension bearings, engine Putters; electrical and electronic use of its resistance to solder, natural resistance, UL temperature index of high toughness and good, for the manufacture of inserts plugs, high-reliability plug-ins, cable plugs, junction boxes, wiring leads to the first, the battery case, IC packaging and so on. Hot water equipment for the manufacture of hot water, chemical pump impeller and pump body and the other parts, clean the valve, oil extraction, socket connector, PH meter boiler jacket and so on.

Contact us for your PEEK plastic injection molding project, we will offer you the best quality and price, this is one of the hardest material to mold, but we are professional.

Plastic molding operating principle and maintenance works

/in /by

Plastic molding is a cyclic process, with each cycle including: dosing – molten plastics – Injection pressure – Filling the cooling – Kai-mode pickup. Remove the plastic parts and then re-closed mode, the next cycle.
    1.2 The structure of the injection molding machine
Plastics injection molding machine according to two ways of piston and screw injection molding machine injection molding machine; according to machine transmission mode can be divided into hydraulic, mechanical and hydraulic – mechanical (link) type; divided automatically by operation , semi-automatic, manual injection molding machine.


    (1) horizontal injection molding machine: This is the most common type. Its part and injection mold parts at the same level center line, and the mold is opened along the horizontal direction. Its characteristics are: body short, easy operation and maintenance; machine center of gravity is low, install a more stable; products after the top of the automatic use of gravity down, easy to implement fully automatic operation. At present, injection molding machines on the market to use more of this type.


    (2) vertical injection molding machine: its part and injection mold parts in the same vertical center line, and the mold is opened along the vertical direction. Therefore, its small footprint, easy to place inserts, more convenient loading and unloading the mold, the material from the hopper into the plastics can be more evenly. But the product is not easy automatic ejection after the fall, must be removed by hand, not easy to achieve automatic operation. Vertical injection molding machine should be used for small injection molding machine, generally less than 60 grams in the injection molding machine with more large and medium-sized machines should not be used.


 (3) angle injection molding machine: the injection direction and the interface in the same mold surface, it is particularly suitable for machining center parts of the plane not allowed to leave the gate traces of products. It covers an area smaller than the horizontal injection molding machine, but it inserts into the mold easily tilted down. This type of injection molding machine should be used for small machines.


   (4) multi-mode rotary injection molding machine: it is a special multi-station plastic molding machine operation, which is characterized by the rotary clamping device structure, mold around the shaft rotation. This type of injection molding machine injection device into full play the plasticizing ability to shorten the production cycle and improve the productive capacity of the machine, which is particularly suitable for cooling and sizing a long time or place inserts for supporting the time and need more plastic in large quantities products production, but a large clamping systems, complex clamping device clamping force tend to be smaller, so that the plastic molding machines in the production of soles and other products used more often.